Harbor Freight Dust Collector Impeller Upgrade

Since the flex pipe is exactly 4" it won't fit over the 4" PVC. Alright, enough talk, here is how I upgraded my Harbor Freight Dust Collector. The baffle is roughly the same. Transfer the gasket if it is on the old flange, if not move to installing new flange on the impeller housing.

Harbor Freight Dust Collector Impeller Upgrade Your Browser

My now old, circa 2009 Central Machinery 2HP dust collector that I bought from Harbor Freight on sale and with a 20% off coupon, has always worked okay, but I want more than okay. The motor mounted to the top of the baffle dictated a riser for the bag/filter body so that the impeller housing outlet lined up with the bag/filter inlet. This ensures full close or full open when the handle is flush with the body. My pipe height was dictated by counters. Lowering the jack lowers the trash can from the Thien baffle, allowing me to dump it. 5" sections (or a coupler depending on your setup). At a home shop it's more for comfort and to avoid small shocks. Harbor freight dust collector impeller upgrade your flash. When you have to install a reducer, a tapered reducer is preferred to help airflow.

Harbor Freight Dust Collector Impeller Upgrade Your Flash

As you can see from the above picture there is a grinder. 25" reducers from harbor freight. I considered a Thien baffle and a cyclone. What is a good source for 6" DWV pipe and fittings?

Harbor Freight Dust Collector Impeller Upgrades

A quarter of an inch is inside the channel on the top and bottom plate. It was backordered and took a while to get to delivered. The inside clear height is 4. Align the new impeller bore / keyway to the key / shaft, and wiggle it a bit until it just barely starts to go in.

Harbor Freight Dust Collector Impeller Upgrade Kit

2 HP Dust Collector. Normally, the Rikon impeller is the suggested upgrade part, but since those are apparently gone forever, this part seems to be a straight up equivalent. Replace safety key and / or plug dust collector back in. Keep the trust washer with the screw in the orientation it came off. The first piece of equipment I connected was the belt sander.

Harbor Freight 2Hp Dust Collector Impeller Upgrade

5" piece of 4" PVC on each side of the gate. Once particles accumulate they can be easily cleaned by emptying the bag. While I could get rather simple ones for a few bucks, I don't want a gate with a track that will eventually fill with sawdust and impede operation. 2) 4" PVC pipe cut to 2. Harbor freight dust collector impeller upgrade kit. The wire acts as an antenna rather than a conductor in a circuit. The impeller is from a Rikon dust collector.

Cost - $20-50 depending on how much scrap you have. 75"x6" 1/2" MDF Gate Body - 4 3/16" hole for the pvc pipe or 4. I did a lot of research in how to set up the piping. Size up, and select the proper drill bit for drilling metal. Total Cost: $600 range depending on various factors.

Unfortunately I don't have a lot to put towards something, but does anyone have any suggestions for a minor step up? Initially I planned to cut couplers in half for each side of the gate, but that would just add an extra joint between the wye and the gate since I will install the gate right off the wye. The motor outlet will feed directly to the filter bag. I bought a Wynn filter for two hundred dollars. Dave's Workshop Blog: Central Machinery (Harbor Freight) 2 HP dust collector upgrades. The EVA tension fits inside the pipe. To reduce the amount of dust that reaches the filter and to reduce any wood chips that could hit the impeller, you need a chip separator. Using proper PPE drill the holes. The modifications to the dust collector are.... - Replace the 20 micron bag filter with a. This allows the flex pipe to fit over it and it fits inside the 4" PVC out on the blast gate.

But, it's out of stock for 3 more months and costs $120 (plus shipping). Not sure if I will paint or not, but the initial feel is good & I'll know better once it's hooked up, I did notice it is a little quieter, maybe the air filter vs bag??? You want to maximize air flow which means as many straight runs and as few curves as possible. I created a circle cutting jig for the of my gates had too much resistance to slide smoothly after glue up of the body. So much sawdust would end up on the ground that Courtney joked she could make sawdust angels. That channel runs right into the bottom slot. ONEIDA Dust Sentry Level Sensor. I can't wait to work on my first woodworking project with my new upgraded dust collector. While you can buy trash can tops that mimic the design and some designs have the baffle completely inside the trash can, I wanted the PVC pipe to run straight into the baffle with no 90* turns. Harbor freight dust collector impeller upgrade your browser. The longest run is 41', using a handheld anemometer, here are the results. There comes a time when you work on enough DIY woodworking projects that a shop vacuum just won't cut it anymore. Super simple process and by far the easiest upgrade. Materials for Thien Baffle: Plywood top and bottom (roughly 18"x18").

Previously the dust filter bag and the dust collection bag were stretched skin tight with and open 4" hose 6 feet long. Blast gates restrict air flow to one tool, otherwise you wouldn't get enough suction. Suction is better with only one pickup, but ultimately I decided to employ two pickups. Enlarge the ports of machines when possible. Once the bolts are removed the impeller is very accessible.
Sun, 28 Jul 2024 23:31:44 +0000