How To Put A Belt On A Craftsman Fs5500 Riding Lawn Mower

Loop the flat side of the belt over the two idler pulleys and feed the loose end of the belt forward towards the clutch pulley position. Slide the deck under the tractor and center it front to back and side to side. Ensure the belt is completely in the pulley grooves. How to Put a Belt on a Craftsman FS5500 Riding Lawn Mower.

Craftsman riding lawn mower belt
Belt diagram for craftsman riding mower
Craftsman riding mower deck belt diagram

Craftsman Riding Lawn Mower Belt

Check the entire belt for proper routing and alignment in all the pulley grooves. If necessary, refer to the photo you took after removing the mower deck from the lawn tractor. Reach underneath and remove the belt from the electric clutch pulley situated in front of the deck. Set the parking brake, place the clutch lever in the "Disengaged" position and lower the attachment lift lever to its lowest position. Belt diagram for a craftsman riding mower. The second mandrel pulley is located directly across from the first mandrel pulley, on top of the mower deck. Point the mower deck suspension arms towards the front. Repeat by disengaging the right rear lift link from the right lift arm bracket situated on the upper rear of the deck. Remove the retainer spring and washer from the anti-sway bar connected to the right rear lift arm bracket. Attach the right rear lift link by lifting the corner of the deck and positioning the slot in the end of the link over the pin protruding from the rear lift arm bracket. This pulley may have a small belt guide that looks like a narrow piece of metal sticking up beside the pulley.

Belt Diagram For Craftsman Riding Mower

During normal mowing operations on an established lawn, the deck belt on your Craftsman FS5500 riding mower usually lasts for two or three mowing seasons. Remove all dirt and grass clippings from around the pulleys and the upper deck surface with a stiff-bristle brush. Turn the engine off and remove the ignition key. Lift the anti-sway bar and insert the far end into the hole in the left transmission bracket. Belt diagram for craftsman riding mower. If you forgot to take a picture of your mower's deck belt before removing it, refer to your mower's owner manual for the correct routing pattern. Take note of the belt configuration and remove the old belt from all drive and idler pulleys. Put the screws inside the covers and lay them aside. Go to the other side of the mower and disengage the left front suspension arm and left rear lift arm the same way. After graduating from the University of the Witwatersrand and qualifying as an aircraft engineer, Ian Kelly joined a Kitchen remodeling company and qualified as a Certified Kitchen Designer (CKD). Wrap the belt around the idler pulley in the same pattern as the original belt. Reinstall the two outer mandrel covers and tighten the screws securely.

Craftsman Riding Mower Deck Belt Diagram

Remove the old belt from the mandrel pulley located on top of the mower deck near where the cut grass discharges. Williams is a winner of Writer's Digest Magazine's annual writing competition. Replacing the deck belt on your Craftsman lawn mower is a relatively easy operation once the mower deck is removed from the lawn tractor. Install the new belt onto the mandrel pulley with the large belt guide by slipping it between the pulley and the guide. Craftsman riding mower deck belt diagram. Repeat and attach the left rear lift link the same way. Slide the mower deck out from under the right side of the tractor.

Grasp the forward-facing belt tension rod on the upper left of the mower deck. But when mowing through unfinished areas, friction caused by flying dust, gravel and debris causes abnormal belt wear. Slide the loose front section of the new belt over the electric clutch pulley. Slip the belt off the pulley by hand. Reconnect the front link and secure it to the pin on the chassis with the washer and retainer spring removed earlier. Reach under the right rear of the mower deck. Wind the belt onto the mandrel pulley near the grass discharge. Secure it with the washer and retainer spring removed earlier. Once free, ease the end slowly upward to release tension on the mower deck belt. Maintain a firm grip, lever downward and push the end toward the tractor to disengage the spring-loaded rod from the slot in the lock bracket. Remove the belt from the second mandrel pulley by using your hands to slip it up between the large belt guide (a half-dome shape) and the pulley. Kelly then established an organization specializing in home improvement, including repair and maintenance of household appliances, garden equipment and lawn mowers. Remove the retainer spring and washer by hand from the pin protruding through the hole in the front right suspension arm located on the upper front of the deck, and then disengage the link.