1St Gen Suspension Torque Specifications

Just now going to bed at 7AM thanks to this little SNAFU. A torque wrench for re-installation of critical components. Get live shipping quotes on JBA web sites. This is best done with a ball joint pressing tool that utilizes a large C clamp type press that pushes the joint apart. Head bolts: 29 ft-lbs + additional 90 + another 90 (2RZ/3RZ). 1st gen tacoma lower ball joint torque specs pictures. Parts are straight forward - you need ball joints and bolts. To replace the front shocks on the Toyota Tacoma you will need to lift the vehicle up into the air and start by removing the tire on the side you want to replace. Upper ball joint to upper control arm: 80 ft-lbs.

1. 1st gen tacoma lower ball joint torque specs pictures
2. Toyota tacoma lower ball joint
3. Toyota tacoma lower ball joint replacement
4. 1st gen tacoma lower ball joint torque specs by size
5. 1st gen tacoma lower ball joint torque specs pdf

1St Gen Tacoma Lower Ball Joint Torque Specs Pictures

Start to remove it completely. Pliers for the various cotter pins (cutting) (needle nose). On the Toyota Tacoma there are two control arms being the upper and lower control arms. Will be doing my LBJs here in about two weeks. Because that is what I will want to run for my lower ball joints. 14mm socket to remove the four bolts holding the LBJ to the spindle.

Toyota Tacoma Lower Ball Joint

Pressure plate to flywheel: 14 ft-lbs. It takes to come off so that I can then use the same number when installing the new part. Product must have been purchased from us and not a dealer. 1996-2000. use a flanged bolt, part #90080-10066. Now, why they chose weaker bolts, who knows. 1st gen tacoma lower ball joint torque specs by size. Axle u-bolts: 90 ft-lbs. If you do have a rubber dust covers on your LBJs, you need eight (8) of "black" (washer) bolts. Front Wheel Hub Installation. Shift lever retainer: 29 ft-lbs (2RZ/3RZ), 13 ft-lbs (5VZ). Toyota Tacoma Wheel Hub Torque Spec: 100 ft-lbs. These bolts are torqued to 37 ft-lbs. Back up the nut on the middle of the tie rod to ensure it does not move your alignment. OTC 6295 Front End Service Set.

Toyota Tacoma Lower Ball Joint Replacement

A 3% processing fee is deducted from all refunds. 4 bolts that hold it in place. This nut can be tightened down to 112 ft-lbs and then a cotter pin can be installed. Note: You will end up with a stronger LBJ - regardless of rubber dust cover use - by using the black bolts. Location: Orange County, CA. As these are removed the shock will separate from the vehicle and.

1St Gen Tacoma Lower Ball Joint Torque Specs By Size

1993 Corolla Wagon 7AFE. That is because they create a tighter joint when torqued to 37 ft-lbs than the older, "green" flanged head bolts (which were torqued to 59 ft-lbs). Lug nuts: 83 ft-lbs. Step-by-Step Replacing Lower Ball Joints (LBJ) on a 1st Gen Tacoma (or 3rd Gen 4Runner) –. "Green" Flange Head LBJ Bolt (90105-10406). Hey Jordan, there are some pics of the bolts in the Prado 90 Series forum link I provided, if that helps. If you also need 4 bolts, then you have two choices: - Best: If you'd like to use the (better) "Black" bolts (w/washer) to secure the LBJ to the lower control arm (LCA), purchase LBJs and bolts separately: - Good: A kit that includes "Green" flanged bolts to secure the LBJ to the lower control arm (LCA), are sold as part numbers - L: 43340-39585; R: 43330-39815.

1St Gen Tacoma Lower Ball Joint Torque Specs Pdf

Some red or blue loctite when installing these bolts to ensure they do not loosen up and cause an accident. Once the vehicle is in the air you can remove the corresponding tire for the side that you want to change the. However, note that it does not come with LBJ bolts or castle nuts. Be sure not to ruin any of the bolts threads if you end up using a hammer to. Steering rack mounting clamp: 123 ft-lbs. Sorry, had a shitty night. 1ST Gen Suspension Torque Specifications. Once removed you can now tap out the tie rod from the spindle and. This was brought to my attention by somebody posting the following information on our YouTube video for this job.

The torque specs for the inner tie rod are 50 ft-lbs. Toyota has a recall on some model year Tacoma LBJs. The inner part of the tie rod uses an nut that will need to be removed, this nut may spin depending on how. ARP bolts 8740 chromoly = 180-210ksi. 25 bolts about 30mm long.

Installation of this system will alter the center of gravity of the vehicle and may increase the risk of a roll over as compared to stock. Steering wheel set nut: 26 ft-lbs. You are currently viewing as a guest! Communicate privately with other Tundra owners from around the world. Toyota tacoma lower ball joint replacement. The dust covers I believe are just extra protection for the rubber boots of the balljoint so it doesn't get torn possibly from road debris or trail debris. Since there is not a lot of room. Fast forward to a couple weeks back, I was pulling the LBJ to service my CV axles and half of the bolts were stretched..

This backs up what I was told by the guy commenting on our video and what was explained in that Prado 90 Series forum link I provided. Guides are intended to assist in each procedure to help diyers with the job. Once the bolts have been removed you can take off the hub. Air Intake Chamber: 15 ft-lbs (2RZ/3RZ), 13 ft-lbs (5VZ). How important is it to torque them to 59ftlbs? Just joined the list of people with failed lower ball joint bolts. Companion flange nut to transfer output shaft: 87 ft-lbs. With these bolts removed the entire brake system can be placed to the side, be weary of the brake hose that connects to the.