Hurricane Shutter Hardware & Parts For Any Brand Shutter

Wing nut 1/4"-20 zinc weather protective coating. Start on left side of opening with first panel. You will not need a diagram. One of the biggest mistakes many Florida homeowners make prior to a major storm is failing to pre-label storm shutters. We recommend plywood over OSB because the OSB must be about 1/3 thicker (or 5/8" thick) to provide the same impact resistance as 1/2" thick plywood. PanelMate anchors, the original 'direct mounting' anchoring system, is one of the most cost-effective ways to install hurricane panels to concrete, block or wood structures for ultimate storm protection. Cost will likely be an important consideration when deciding whether to do it yourself or not. Generally Used in Wood Frame Homes. Do not pay in advance for take-down as a lot of people have hardship or too much work to do after the storm and may not be able to return to finish the job. Copyright 2006-2023 Hurricane Shutters Florida. STEP 3: Insert the stainless steel screen into the pre-cleaned hole; in some cases it is easier to put the screen into the wall first and then fill it with epoxy. Connect to view prices. Easy to install on any existing home. This is a Blow Out Bulb used to blow the excess dust out of a hole after drilling.

Hardware for hurricane shutters
Wing nuts for hurricane shutterstock
Hurricane panel wing nuts

Hardware For Hurricane Shutters

A top u-shaped header is attached above the opening, and a bottom F-track is attached below the opening. Locate your manual hand crank. This nuts tools A must have for hurricane snowstorm prone areas, storm shutters and hurricane shutters which use wing nuts.

Wing Nuts For Hurricane Shutterstock

WHAT ARE THE BEST TYPES OF STORM SHUTTERS? Call us at 239-369-8600 to get help and get the right parts. There are several ways to secure windows and doors, whether you install ready-made hurricane shutters or panels, or simply attach exterior grade plywood to your structure (which happens to be most frequently done here in Florida). Check with your building department for local requirements. Sleek European-Styling. In hurricane prone areas you can find various kinds of shutter system kits at some home improvement stores.

Hurricane Panel Wing Nuts

So whether you need the actual panels themselves or the mounting hardware to get them up correctly on your property we can help. Make sure to clean the dust out of the hole before inserting the anchor, the hole should be blown out with forced air to eliminate excess dust. Hurricane and Storm Fasteners: PanelMate Anchors. Overall Size: 29 x 15 x 14mm / 1. Ivy Classic 45630 2-1/2" Wing Nut Driver. All cordless drills have a clutch setting as in picture above.

We carry a full range of shutter parts, regardless of brand. The advantage of the Sammy is it will work where you may have deeper veneers or trims, or where you need to seal the fastener into the wall to prevent moisture penetration. 19 inch) widePackage Include: 1 pcs x Nut DriverHow To UseJust pop it into a power screwdriver and get the wing nut / shutters installed without concern about spraining your thumbs by using other hardware tools, saves wears and tears on your fingers. Choose Zip at checkoutQuick and easy. Drill a hole in ONE side only. Recruit your neighbors and friends to help install storm shutters. Lead screw or lead split screw anchors are not considered vibration resistant in concrete and masonry installations. Homeowners also have the option of painting the exterior of the snap track to match their home. We Stock a Large Varity of Fasteners That are used in the Installation and Production of Hurricane & Aluminum Parts. Countersink for the PanelMate anchor where required or desired, or use combination bit to perform the drilling and countersinking operation. The picture at left is a cutaway of a wall; you can see the finish, the sheathing, and the framing. IMPORTANT: These instructions (courtesy Powers Fasteners, Inc) are provided as an example of how the system is used and do not replace the specific manufacturer s written instructions when using these systems. Hollow Masonry Block Walls and Brick Veneer: Typically the most difficult permanent anchor installations to get right are on hollow masonry walls or walls with brick veneer.